Home 2017

Switchmate Bright instant smart lighting switch review

Last year I reviewed the original Switchmate Smart Light and now they have recently come out with version two which they’ve named the Switchmate Bright. Let’s give this smart light switch controller a try.

What is it?

The Switchmate Bright is a wireless controller for your existing light switch (toggle or rocker style) that physically toggles the switch on and off with your smartphone or a simple touch.

What’s in the box?

Switchmate Bright
2 AA batteries
Switchmate stickers
Instructions

Design and features

The new version of the Switchmate is significantly smaller (narrower) than the original version.  It is available in white or ivory. I was sent the white version.

It’s made of plastic with a touch-enabled switch on the front and a motion sensor at the top.

On the back of the Switchmate are two magnets that help this device achieve an almost install because absolutely no tools or wiring is needed. It uses the magnets to stick/attach to the existing light switch cover.

The slot on the back of the Switchmate fits over the light switch and a motor inside the Switchmate manually flips the light on and off.

Installing the Switchmate Bright

Installation is about as simple as it can get. First, you slide the battery cover off the back of the Switchmate, insert the included AA batteries, and put the cover back in place. According to the Switchmate FAQ, batteries should last between 8 and 12 months before they need to be replaced.

Then you install the iOS or Android version of the Switchmate app on your mobile device. The app will guide you through the rest of the setup which asks you touch the switch on the front of the Switchmate so the app can detect and connect to the switch via Bluetooth LE. Switchmate does not use WiFi or need an active connection to the internet to work.

Then you place the Switchmate Bright over your existing light switch with the switch in the ON position. The magnets on the back of the Switchmate make contact with the screws in the switch cover to hold it in place.

That’s it. You’re done. Plug and play.

Using the Switchmate Bright

After the Switchmate Bright has been installed, you can touch the front of it to toggle the switch on or off. You can also use the app to toggle the switch, have the Switchmate set to turn on the light when motion is detected, set the switch to turn on and off at predetermined times, or use your voice in the app to tell the Switchmate to toggle the switch.

Using your finger to toggle the light just by touching the face of the Switchmate works every time. When the switch is touched, a blue LED will blink. This is the easiest way to use the Switchmate, but it’s not exactly going to give you a smarthome kind of experience. That’s where the Switchmate app comes in.


The app is where you configure timers, motion detection settings, and can enable the welcome home feature.

There are two timers that you can set that enable you to program the Switchmate to turn the light on and off at the times you specify. You can also have these timers set to repeat based on the day of the week, weekends, and more. The nice thing about the timers is that they work even if you’re not within Bluetooth range of the Switchmate. Once the timer is set, it will happen regardless of the location of you and your mobile device.

The motion detection feature can also be customized to only work during certain hours of the day and you can specify how long you want the light to remain on after motion has been detected.

There’s also the Welcome Home feature that you can enable so that the Switchmate will turn on the lights when you arrive home.

How far is the control range for this switch? The claim is up to 150ft. My house isn’t that large, but I was able to control the Switchmate that I installed downstairs from upstairs at the other end of the house. And the nice thing is that the app will show you if the light is on or off by the way the onscreen control button looks. If it’s dark, the light is on and if it’s light, the light is off.

Like the original version of the Switchmate, there can be a slight lag when you press the onscreen button in the app and when the switch actually toggles. The delay is the longest after not using the switch in awhile. But is lightning fast if you toggle it again.

And just like the first Switchmate, there is still a motorized sound when the switch activates.

Voice control

The Switchmate will soon work with Alexa, but for now, you can tap the microphone button in the app and use your voice to tell the named switch to turn on or off.

The voice commands you use for the Switchmate begin with “Turn” and then the name of the Switchmate switch and finally the function which is “Off” or “On”. For example, if I named my Switchmate “front porch” and I wish to turn it off then I would press the microphone in the upper left-hand corner of the app and would then say “Turn front porch off” and Switchmate should turn that light off. I didn’t have a lot of great success using my voice to control the Switchmate. It took more time repeating my command than just tapping the button for the light in the app to toggle it on or off.

Final thoughts

If you’ve been thinking about adding a smart lighting feature to your home but didn’t want to buy brand new bulbs for all your light fixed or deal with hubs, wiring, etc. The Switchmate Bright is one of the easiest ways to add digital control for your lights. Just open the package, install the batteries, install the app, slap the Switchmate over your existing switch and you’re done.

I like gadgets that are easy to install and just work. The Switchmate Bright is that type of gadget.

Source: The sample for this review was provided by Switchmate. Please visit their site for more info and Amazon to order.

 

Product Information

Price: $39.99
Manufacturer: Switchmate
Retailer: Amazon
Pros:
  • No tools needed installation
  • Simple application
  • Timers, voice control, and motion detection settings
  • Does not require an internet connection
Cons:
  • None

Filed in categories: Reviews

Tagged:

Switchmate Bright instant smart lighting switch review originally appeared on on July 14, 2017 at 1:42 pm.

Note: If you are subscribed to this feed through FeedBurner, please switch to our native feed URL http://the-gadgeteer.com/feed/ in order to ensure continuous delivery.

Deal: Save 15% off SOG knives including new BladeLights which have LEDs built into the handle

For those of you who like to be prepared by carrying both a knife and a flashlight, the fine folks at SOG have just made your EDC a bit lighter and less bulky with their new BladeLight series of knives. Available in both folding and fixed blade styles, BladeLights feature 30-45 lumen LED flashlights directly into the knife’s handle.

Why would you want or need a knife with a built in flashlight? One word folks: zombies! If it’s dark and you’re in a horde, you need some light so you’ll know exactly where to aim the blade.

Seriously though, BladeLights are available a folding style knife that has a 3-inch stainless steel blade and a glass reinforced nylon and aluminum handle.

There is also a fixed blade BladeLight like you see above and a filet style BladeLight not shown. All of the BladeLights are powered with easy to find batteries like CR2032 coin cell and AAA batteries depending on the knife style.

Today only, you can save 15% off all SOG & Tool Logic knives and flashlights with coupon code ‘SOG15X’. Hurry though because the sale ends at midnight tonight!

Filed in categories: News

Tagged: ,

Deal: Save 15% off SOG knives including new BladeLights which have LEDs built into the handle originally appeared on on July 14, 2017 at 12:27 pm.

Note: If you are subscribed to this feed through FeedBurner, please switch to our native feed URL http://the-gadgeteer.com/feed/ in order to ensure continuous delivery.

Armor-X iPad Pro cover review

I love my 12.9″ iPad Pro, but, like most folks have mentioned in reviews, I find it a bit difficult to balance when trying to carry it around during use. I’ve found a case that I like for use around the house or on the road, but it’s more a stand, even though it has a hand strap. When Julie offered the team the Armor-X cover for iPad Pro, I pondered if it would be right for my needs. They sent it for testing, and I’ve had it a week or two, so it’s time to report on the results.

Note: Photos may be tapped or clicked for a larger image.

The Armor-X case is made up of three pieces: a two-piece inner hard plastic frame, and a tough rubberized outer case that seals the two together, as well as adds a hand-hold and stand on the back.


The stand is folded under where the hand strap spans, and there is a circular insert in the back of the case to allow it to rotate.

You can hold it in any position, and there is no need to worry that the iPad will slide out of the case. It is firmly attached to the handgrip, and the leather strap is easy to adjust to your hand. I am not able to comfortably get my thumb around the edge while holding the grip, but those with larger hands may. If using in a portrait mode, similar to a clipboard, you’ll find it a natural for sketching, taking notes, or annotating a checklist, as you would with paper.


The ports and buttons are nicely protected. There is a snap-over cover for both the headphone jack and charging port. I was able to use most of my cables without incident.

The buttons are clearly marked, and work well in the case. The sound, funneled through louvered openings (see picture above with green headphone cable), does not appear muffled in any way. There are openings for the cameras, touch sensor, and microphones. The touch sensor is perhaps the only thing you may find a bit compromised. Given its position at the edge, and the thickness of the case (shown in the picture above with white charging cable), you may have an issue getting it to read your fingerprint from some angles. I have both of my thumbs scanned twice in my preferences, which gives me a better chance of having either one read by the sensor, but your mileage may vary. For Apple Pencil users, charging can be an issue, and there is no clip, silo, or other holder for the Pencil or any other stylus. The Pencil, because it is heftier in diameter than most cables, doesn’t fit perfectly into the port. You can wiggle it around and make it charge, in a pinch, but it’d be better to connect a cable and the Pencil adapter, to prevent any incidents with the port or your Pencil.


The stand is a nice touch, but will probably not be used as much as the handle. It slides down from under the hand strap and only will support the iPad in landscape orientation. It will almost stand up in portrait, but not steadily enough to be comfortable in use. If you need to quickly write up a report and have a keyboard in your bag, it’s going to be very comfortable. I wrote this entire article with the stand on my kitchen table using my Logitech K811 keyboard. I love using this iPad with a Bluetooth keyboard.

There is no pass-through for the Smart Connector in this case, which may be a turnoff for some potential users, but with the dearth of accessories that work with that connector, I don’t really see this as a negative. If there is a sudden influx of compelling Smart Connector chargers, stands, or other peripherals, that might change. The only such item I’ve seen that would make me think twice is the Logi charger stand, but I don’t think a lot of folks have this stand.

With the iPad installed, it’s a bit hefty at 40.8 ounces (yes, that’s 2.5 pounds!), but the iPad itself is 1.5 pounds buck naked. Adding this much protection and functionality for only another pound is not too much, in my opinion. I found that even with the added weight, the iPad is actually more manageable than the bare unit itself. Part of this has to do with the size of the device itself. Being so thin, yet so large, it’s hard to manage holding it with one hand trying to wrap around the edge. It’s just too skinny. With this case, however, it has added thickness, as well as grip, even before considering the added convenience of the built-in handhold on the back.

 

While it’s great for those who use their iPads Pro while holding it for moderate periods of time, I don’t have that kind of need in my life. (In the picture above, I’m holding the iPad with my left hand while wielding a DSLR in my right. And I’m more worried about dropping the camera than the iPad!) A building, fire, or home inspector, teacher, lecturer or other professionals who want to have a good list or notes while walking around or standing before a group sans podium would benefit from this case. Next time I demo iOS to a large group, I’ll be using this, so that I can get the most image on the display, and can see what I’m presenting. I’ve done similar workshops with iPhones and regular iPads, and it’s great to have a case that lets you gesture with one hand while securely holding the device in the other.

Source: The sample for this review was provided by Armor-X. Please visit for more info.

 

Product Information

Price: $35
Manufacturer: Armor-X
Requirements:
  • iPad Pro 12.9
Pros:
  • Rugged and durable
  • sturdy hand-strap grip
  • stand for sitting in Landscape
Cons:
  • Stand is a bit fiddly, doesn't work in Portrait
  • No holder for Apple Pencil

Filed in categories: Reviews

Tagged: ,

Armor-X iPad Pro cover review originally appeared on on July 14, 2017 at 8:00 am.

Note: If you are subscribed to this feed through FeedBurner, please switch to our native feed URL http://the-gadgeteer.com/feed/ in order to ensure continuous delivery.

Microsoft is giving away eleventy bazillion eBooks. Go get em!

Did you know that around this time every year that Microsoft gives away a selection of eBooks? Me neither, but now I know because former Gadgeteer writer Leah Gail Hallet sent me a text message this morning with a link to the giveaway page. One word: Wow! If you’re looking to build out the technical section of your digital library, then today is your lucky day friends. 

Microsoft is giving away eBooks on dozens of topics including Windows 10, Office 365, SQL Server, Excel, OneNote, Surface Book, Surface Pro and much more. The eBooks are in various formats including EPUB, PDF, DOC, and MOBI, so they can be read on a variety of devices. And best of all, you don’t have to jump through ANY hoops to download these eBooks. Just click on the individual links for each book or download the whole batch at once. You don’t have to give them your email address or anything. Head over to the Microsoft eBook giveaway page and have fun and thank Leah Gail for sending me/us this link.

Filed in categories: News

Tagged: ,

Microsoft is giving away eleventy bazillion eBooks. Go get em! originally appeared on on July 14, 2017 at 7:10 am.

Note: If you are subscribed to this feed through FeedBurner, please switch to our native feed URL http://the-gadgeteer.com/feed/ in order to ensure continuous delivery.

Modarri car building sets review

If you think back to your favorite toys when you were a kid, were they video games or were they toys that let you use your imagination like construction sets and other building toys? I’m going to show my age here, but some of my favorite toys when I was a budding gadgeteerling were Lincoln Logs, Tinker Toys, and an Etch A Sketch. I spent hours playing with these toys because each time I built or drew something, it was new. You can still buy those classic toys today, but if you’re looking for a new toy for your kids that promotes creativity and open-ended play, check out Modarri. They call it the Ultimate Toy Car. Let’s see if that’s true. 

What is it?

Modarri are car building sets designed for kids and those who are still young at heart. Each car building set comes with at least one car and individual parts that you can mix and match to create different looks.

In the image above, you can see what is included in a single car set. The single car set includes 6 frame pieces, a set of wheels, and a hex screwdriver.

Although it’s not obvious, you can even mix and match tires and seats if you have more than one car.


The wheels feature real suspension and shock absorbers.

The Modarri car frame parts stack on top of each other and are held in place with two screws.

The hood goes on first.

Then the fenders.

And then the metal frame that has the screws which are retained in the frame so that they won’t fall out and get lost.

The whole idea of the Modarri car building system is that you can mix and match the parts to create new cars.

Three car sets like the one shown above contain extra parts like the traffic cones and additional screwdrivers. And of course, the more pieces you have, the more variations of cars you can build.







All of the car parts except the metal frame with the screws and some of the wheel mechanism are made of plastic. The parts feel rugged enough though, so they should be able to stand up to some rough play.

Building the cars isn’t the only fun kids can have. You can also “drive” the cars by putting your finger in the seat. Since the wheels have built-in suspension, you can actually steer the cars, which is fun.

Modarri also offers a carrying case so you (I mean your child) can keep the cars, parts and tools organized and tidy.

The case can hold a dozen cars and has a removable tray and a handle for easy transport.

Final thoughts

So is Modarri the ultimate toy car building set? Yes, it is. These cars are a lot of fun to assemble, disassemble and “drive”. The system is very LEGO-like, but the Modarri cars look a lot more like a real car than any LEGO car does.

If your child likes to build things and likes race cars, Modarri car building sets are sure to keep them (and you) entertained for hours.

Source: The sample for this review was provided by Modarri. Please visit their site for more info and Amazon to order.

 

Product Information

Price: $19.99 and up
Manufacturer: Modarri
Retailer: Amazon
Pros:
  • Promotes creativity and imagination
  • Many possible design combinations
  • Easy to assemble and disassemble
  • Screws attached to frame
Cons:
  • Can get expensive if your kid wants to collect them 😉

Filed in categories: Reviews

Tagged: ,

Modarri car building sets review originally appeared on on July 13, 2017 at 10:39 am.

Note: If you are subscribed to this feed through FeedBurner, please switch to our native feed URL http://the-gadgeteer.com/feed/ in order to ensure continuous delivery.