Koogeek BP2 blood pressure monitor review


I don’t take my blood pressure on a regular basis, but maybe I should.  I have EMT training so I own a manual sphygmomanometer (“blood pressure cuff”) as well as a tabletop automatic and a portable. The Koogeek BP2, however, looked so small and sleek, I knew I had to give it a try.

The BP2 comes with a microUSB charging cable and documents.

  • Length (Fold): 150mm
  • Width (Fold): 75mm
  • Thickness (Fold): 85mm
  • Weight: Approx. 300g
  • Cuff Size: Approx. 220-360mm
  • Battery: 400mAh lithium charged via MicroUSB. Good for at least 50 times of continuous usage on one charge.

The top of the BP2 consists of (left-right) a microUSB charging port, reset button (recessed), LED and power button.

The BP2 reminds me of an iPod Mini.

Here’s a close-up of the cuff.  Check your upper arm circumference before ordering.

The BP2 also includes wireless connectivity to your Android or iOS device. I started to install the App, and came across this:

Why do I have to give them my email and password just to start cuff inflation and take a reading?  The app logs your blood pressure measurements, but I don’t see why you can’t just write it down yourself.  I guess I’m old fashioned that way, and I don’t feel like sharing my health information in this manner.

In the instructions, I found this note about not using your cell phone near the BP2.  I’m not sure someone proofread this. Why have a companion app, then?

Even more troubling was this note in part 4, “After the measurement”.  Why would the BP2 upload your readings to the server if you don’t launch the app?

Fortunately, for the paranoid-minded like me, you can operate the BP2 without the app.  Simply power it up, and press the power button a second time to begin cuff inflation.

As you can see in the video, the BP2 display shows systolic (the “upper” number) and diastolic (the “lower” number) plus heart rate.

But is it any good?  I was a little concerned when I saw my readings.  They were high for me.  So over the course of an hour, I took my blood pressure at rest using different methods.

Koogeek BP2:  125/74

Hyundai upper-arm portable:  118/75

Omron desktop: 114/77

Manual cuff with stethoscope: 115/80

On average I noticed the Koogeek BP2 measured about 10 mmHg higher than what I think is normal for me.  That’s not reassuring. It could be an individual error. I also noticed the screen went blank after giving a reading in about 10 seconds. If you don’t use the app, I would note the reading or write it down quickly.

Source: The sample for this review was provided by Koogeek. Please visit their site for more info and Amazon to order one.

Filed in categories: Reviews

Tagged:

Koogeek BP2 blood pressure monitor review originally appeared on on June 28, 2017 at 8:30 am.

Note: If you are subscribed to this feed through FeedBurner, please switch to our native feed URL http://the-gadgeteer.com/feed/ in order to ensure continuous delivery.

Fugoo Style S portable Bluetooth speaker review


Here we go again, another season, another Fugoo speaker. Fugoo is a wireless Bluetooth speaker maker that has always been just outside  the heavily advertised mainstream of Beats, JBL or Bose. That’s too bad, because Fugoo consistently makes some of the best wireless speakers available. For this long, hot summer of 2017, Fugoo has improved on their original Style speaker with the larger and much more powerful Style S speaker—but not without some trade-offs.

It’s been fun to watch Fugoo evolve from dedicated individuals with a single (but incredible) idea for a speaker that was unlike any other at the time to a company intent on broadening their market. Fugoo now makes four different models—three based on that first speaker. First was the original Fugoo speaker which consisted of a single speaker that could be housed in three differently styled shells. That was followed up by a twice as big XL version of that same idea. And it worked—loudly. Then came the Go speaker—a more affordable departure from the form and function of the previous speakers. The Go has it’s plusses and minuses, but it’s the least expensive speaker Fugoo makes and still sounds great for its size and purpose.

However, Fugoo’s speaker lineup had a gap between the original and much larger XL models. Which is where the Style S fits. The Style S sits between the Style and Style XL in both price and size. Visually, it looks just like the other Style designed speakers, but there are some important differences under the hood. More on that later.

Like all the other Fugoo speakers The style S is IP67 waterproof rated, which means the speaker can be 3 ft. under water for 30 minutes and come up sounding just as good—pretty impressive. Plus, it will float if it falls into the water—always a good thing.

The Style S weighs only 1.7 lbs., so it’s easy to tote around. It’s wrapped in a light brown burlap-type cloth that grips easily. If I know Fugoo, other colors will follow. The top of the speaker has the usual volume and play/pause buttons that are shaped like a + and —. Rubberized end caps hold discrete on/off and Bluetooth pairing buttons on one end with AUX and mini USB charging ports at the other end. The ports are protected from the elements by a thick, rubberized cover. The speaker can be tethered to either bicycle handlebars or a tree or pole with an optional mounting kit that attaches to the speaker’s base.


There are four speakers inside the Style S—two full range drivers and two bass radiators. The original (and cheaper) Fugoo speaker has six speakers and the Style XL has eight speakers. However, it’s not the number of speakers that’s important here, it’s the quality of sound the speakers make. The Style S has a 20-watt amp versus the original Fugoo’s 6 watts, which makes a big volume difference whether used indoors or out. The Style S can be cranked up to 93 decibels—pretty loud for a small speaker. All this power comes at a price though. Battery life in the original Fugoo speaker is an insane 40 hours vs. the Style S’s battery life of 15 hours. That’s still long enough for any outdoor party, but it will need recharging more often. Also, unlike the original or XL speakers, the Style S does not have matching speakers on both sides for true 360° audio. The front of the Style S has both drivers with one of the bass speakers. The rear has only the other bass speaker. I don’t think whether the audio is 360° or not is that big of a deal, but it is worth noting.

The cloth covering on the Style S didn’t feel like there was as much cushioning underneath as on the original Style speaker. It made me wonder if the covering will wear out with repeated use over time, especially in spots where fingers are placed when gripping. Only time will tell. The original Fugoo speaker’s cover just feels better to hold—and two years later, it still looks and feels new. Note that the Style S shell is not removable as on the original or XL speakers.

Bluetooth pairing is quick and simple whether it’s a smartphone or a computer. But here’s what makes the Fugoo Style S so cool—stereo Bluetooth. Sure, most single Bluetooth speakers are technically stereo, but you can’t really hear the separation. But pair two speakers together for true left and right speaker Bluetooth and that makes all the difference! Granted, this requires buying two Style S speakers (Fugoo offers a second speaker discount when purchased together).

When I reviewed the Fugoo Go speaker with its stereo Bluetooth, I marveled at how there seemed to be an invisible middle speaker when listening to music. The same holds true here, but it’s much better sounding—mainly due to the better sounding speakers inside the Style S and more powerful amp. As I said in the other review, I don’t even get this invisible speaker sensation with my regular desktop speakers and those are excellent sounding!

Pairing in Stereo Bluetooth is not as easy as standard Bluetooth pairing. There’s a step-by-step process involving pressing certain buttons in a certain order, but I still had issues with it either not connecting properly or one of the speakers periodically dropping the signal. Sometimes, it could get frustrating. However, once the connections were successfully made, it worked flawlessly. Once again, I cannot state how much of a difference there is in the audio between using only one speaker or using two working in stereo tandem. It’s positively addicting, especially when seated between them at my desk. Wow.

The tonal characteristics of my music was quite pleasing with the Style S. Whether I was listening to classic rock (my favorite genre) or more modern tracks, the Style S didn’t play any harsh notes. In fact, it handled some brighter sounding treble-happy songs with ease. For instance, some early Byrds recordings from the mid-60s can be harsh sounding with some speakers. The Style S exhibited none of that unpleasantness. Their songs sounded smooth with a decent amount of bass without being muddy or too bright sounding.

Frank Sinatra is a standard bearer of quality music and quality recordings—there’s a difference. He had impeccable taste in material but also, his recordings have held up as benchmarks of how to do it right. That’s why his music is often used to test audio equipment. On the Style S, Sinatra’s voice sounds both intimate and expansive, especially in stereo mode.

An obscure song that’s been a favorite of mine is “A Miner and His Music” by Mohave. It’s an eclectic mix of styles and almost scatological stream-of-conscienceness singing that plays well on the Style S. The song makes you feel like you’re on stage with the group as the instruments play around you in space. This song shows off a wide soundstage when in stereo mode.

Fugoo has another winner with the Style S. Even though it works and sounds great as a stand-alone speaker—when paired for stereo, both speakers are much more than the sum of their parts. So if you get two, they can be independently carried around the house and paired together when the music demands some serious listening.

The Fugoo Style S sells for $139.99 and is available now. Visit Fugoo for more information and Amazon to order.

 

Product Information

Price: $149.99 US
Manufacturer: Fugoo
Retailer: Amazon
Pros:
  • Loud and powerful sound
  • Easy to carry
  • Great sounding stereo pairing
  • Rock solid Bluetooth 4.2 connection
  • Waterproof and it floats
  • Large amp
Cons:
  • Shell not removable
  • Two speakers for stereo effect can become expensive
  • Stereo pairing can be frustrating at first
  • Battery range not as good as other Fugoo speakers

Filed in categories: Reviews

Tagged:

Fugoo Style S portable Bluetooth speaker review originally appeared on on June 27, 2017 at 9:00 am.

Note: If you are subscribed to this feed through FeedBurner, please switch to our native feed URL http://the-gadgeteer.com/feed/ in order to ensure continuous delivery.

SCOTTeVEST Hoodie Cotton jacket review


What’s better than a cozy hoodie jacket on a cool day? How about a cozy hoodie jacket that has lots of pockets for your favorite gear? Sound good? Then you will want to read this review of the SCOTTeVEST Hoodie Cotton jacket. Is it too soon in the review to reveal that I love this jacket? 

What is it?

The SCOTTeVEST Hoodie Cotton jacket is a cotton fleece zippered jacket with a hood, and 21 pockets.

Design and features (pockets, pockets, and even more pockets)

The hoodie is made of a cotton/poly blend fabric and comes in Black, Cobalt, Ash, or Maroon. I was sent the jacket in Cobalt. Note that this jacket only comes in men’s sizes. I was sent the jacket in size XS, but sizes go up to an XXXL.

The jacket has a typical hoodie design with long sleeves, a zippered front, and two traditional hoodie pockets on the front.

SCOTTeVEST’s branding on the jacket is minimal, with an embossed logo on the back (it’s actually under the hood in the image above).

And another logo on the left arm.

In the image above you’ll notice the nylon zipper which matches the color of the jacket and has smooth zip and unzip action. The zipper pull is made of metal with a dark gray finish. The hood drawstrings have the same type of metal on the ends.

You’ll also notice the slit in the ribbed cuff. That’s a thumb hole.

Thumb holes help keep the sleeves in place and keep part of your hand warm in cold weather.

When you unzip the Hoodie Cotton jacket, you’ll be greeted with a panel of pockets on both sides. If you’re familiar with SCOTTeVEST jackets, the Hoodie has a similar layout with some of the same features.

Let’s start on the left side of the jacket. Up at the top at the neckline are SeV’s PAN (Personal Area Network) loops and a CollarConnect covered cable run to help you manage the wires of your headphones. There’s also a BudBucket Pocket on each side at collar bone level to hold your earbuds.

Along the edge is a pen or pencil slot and next that is a vertical zippered pocket for your phone that has a mesh panel that allows you to see the screen and even interact with it. I will say that it’s not “easy” to interact with the phone through the mesh panel, but it’s possible.

Below the phone pocket is a zippered pocket that is large enough to hold a tablet like an iPad mini. The pocket is actually large enough to almost hold my Samsung Galaxy S Tab which has a 10″ display, so a 10.5 inch iPad might fit too.

There’s another pocket layered over the tablet pocket what is the perfect size for a Field Notes notebook or a passport.

The right side panel of pockets is almost identical to the left side except that the bottom pocket is smaller and sized more for a pair of sunglasses which is suggested by the embossed icon beside the pocket.

Note that all of the inside zippers are locking zippers. The pull folds over to lock in place to prevent accidental unzipping.

As mentioned before, there are two front pockets on the Hoodie Cotton that look like classic front hoodie pockets, but they hide a few extras. First of all, each one has a top drop zippered pocket that is perfect for your phone, a wallet, and even a small bottle of water.

The main handwarmer pockets have a separator panel so you can put items like your keys in front the panel and your hands in the back or visa versa.

There are also some small Velcro pockets for coins or a key. And the right pocket has a lanyard coil for your keys.

The large hood has a built in do not disturb eye cover so you can take a nap on a train, plane, etc and not worry about someone bugging you. I really love this feature, but I do wish that the do not disturb eye cover had some small magnets or velcro to keep it attached to the inside of the hood. As it is designed, only one edge is attached to the front of the hood. The rest of the eye cover just floats inside the hood.

The SCOTTeVEST Hoodie Cotton fits well even though it only comes in men’s sizes. I am 5’6″, 128 lbs give or take and the XS fits me fine.

My favorite feature are the top down zippered pockets because they let me quickly access my phone.

Final thoughts

As I already said at the very beginning of this review, I love the SCOTTeVEST Hoodie Cotton jacket. It’s warm, soft and cozy enough that I could easily sleep in it. It’s kind of a bummer that it’s summer because I haven’t had a lot of opportunities to wear it now that it’s warmer outside. I did wear it a few weeks ago when I was on vacation and visited Indiana Caverns for a cave tour. The cave was about 50 degrees and this jacket kept me at the perfect temperature and kept all my gear organized in their own pockets.

Next to the SCOTTeVEST Lola jacket, the Hoodie Cotton ranks right up there as one of my all time favorite SeV garments. The price is nice too. If you love hoodies, I know you’ll love this one.

Source: The sample for this review was provided by SCOTTeVEST. Please visit their site for more info and Amazon to order.

 

Product Information

Price: $95
Manufacturer: SCOTTeVest
Retailer: Amazon
Pros:
  • Soft and cozy
  • 21 pockets!
  • Well made
Cons:
  • None

Filed in categories: Reviews

Tagged:

SCOTTeVEST Hoodie Cotton jacket review originally appeared on on June 26, 2017 at 5:30 pm.

Note: If you are subscribed to this feed through FeedBurner, please switch to our native feed URL http://the-gadgeteer.com/feed/ in order to ensure continuous delivery.

StarTech USB/SATA Drive Duplicator and Eraser review


The StarTech Drive Duplicator and Eraser for SATA and USB Flash Drives is a powerful, simple to use, and versatile tool for IT professionals or consumers who routinely need to manage a number of different types of data drives. Although it’s lacking in documentation and is a bit expensive at the suggested retail price of $796.99, the Drive Duplicator can replace a standard computer tasked with the same operations.

The Drive Duplicator comes in standard StarTech packaging, no frills and well-protected with clear indications of the product functions.

What’s in the Box

  • 1 – SATA/USB duplicator and eraser
  • 1 – 12v DC Power supply
  • 4 – Universal power adapters (NA/JP, UK, EU, ANZ)
  • 2 – Drive-connector cables
  • 2 – Drive pads
  • 1 – Quick-start guide

The unit comes with five different types of international power cables, including two for the U.S., one with a ground plug and one with a wired ground.

The design of the unit speaks much to the functioning of it, simple and direct. A glossy back top with four membrane buttons, an LCD screen and 12 LED indicator lights is met on the sides by a textured hard plastic casing.

 

Both sides of the unit have connections for USB 2.0 and standard 22 pin SATA drives. You can use 2.5-inch and 3.5-inch SATA SSDs or HDDs with the unit. The top of the unit has the connection for the power plug and an on/off rocker switch.

To be honest, the rocker switch causes me a lot of anxiety as it can easily be knocked into the off position during vital operations.

The connections on either side of the unit are clearly marked Target and Source. There are separate LED indicator lights (yellow, green and red) for each input.

The quick-start guide recommends always using the included SATA drive connector cables when connecting SATA drives to prevent damage to the SATA connectors on the unit and the drives themselves.

Soft, mousepad-like “drive pads” are also recommended for use when using SATA drives.

For my SATA testing, I used two identical 120gb SSDs connected via the drive connector cables.

For USB testing I used two identical 2gb USB flash drives.

With SATA drives and power plugged in, the unit takes up a good bit of space and is rather unwieldy. Although, considering that it can replace a computer doing the same functions, it’s a small caveat.

All operations are controlled via menus on the LCD screen and the membrane buttons. The menus take a little getting used to at first, but for basic functions like copy and erase, the process is pretty simple to activate. The LEDs indicate drive functions; yellow indicates that the drive is connected correctly, green indicates that activity is occurring, and red indicates that an error is occurring.

The Drive Duplicator supports six erase modes and four copy modes as well as cross-interface support allowing you to copy SATA-to-USB or USB-to-SATA.

One of the most useful functions of the unit drive erasure. I use it daily to wipe USB flash drives that come out of usage rotation and for wiping SATA drives that are being put into new machines. The unit provides you with six different erase modes. The one I use the most is the basic Quick Erase mode, but it also includes Single Pass Overwrite (Full Erase), 3-Pass Overwrite (DoD) Erase, 3-Pass Overwrite and Compare, Secure Erase and 7-Pass Overwrite. The 3-Pass DoD Overwrite is compliant with the U.S. Department of Defense (DoD) secure erase standard; the drive is overwritten three times to make sure data is completely wiped.

The default modes on the unit have a failsafe in place to protect the Source drive from being erased, but with a little trip through the menu-tree you’re not only able to erase a single SATA or USB drive, but two drives simultaneously.

As you can imagine, with bigger drives the multiple overwrite modes take significantly more time. But, as with the copy modes, since the unit’s functionality is hardware based as opposed to software based, it’s still faster than comparable operations on a computer.

For copying, the drive duplicator provides four duplication modes; Quick Copy, All Partitions, Sector-by-Sector (Whole Drive) and Percentage Copy. Again, like erasing, the mode I use the most is Quick Copy. Copy times between SATA drives are very impressive, but when duplicating USB drives, the lack of USB 3.0 support becomes painfully obvious.

At smaller sizes, the copy times aren’t much of an issue, especially in Quick Copy mode. However, when utilizing the cross-interface duplication (SATA to USB or USB to SATA) it would be really useful to be able to access the higher speeds that USB 3.0 offers.

Despite the lack of USB 3.0 support, the copy modes of the unit are still incredibly useful. The compare function of the duplicator is particularly helpful as it checks the drives after a copy has finished to make sure the copy operation was successful. Keep in mind, with any copy mode, the target drive must be the same size or larger than the source drive.

Sector-by-Sector mode is great for creating an exact replica of a source drive. All data and empty space are copied to the target drive so even hidden partitions will be duplicated. I use this mode a lot for testing purposes, creating a backup of an entire drive for safekeeping before I work on the original drive.

Overall, the StarTech USB/SATA Drive Duplicator and Eraser is a great, super useful device with a ton of functionality. Although the suggested retail is $796.99, I found it for significantly cheaper at a number of different outlets. At any of these prices, it’s still a great buy because it basically replaces an entire computer running the same operations. Plus, the Drive Duplicator is backed by a StarTech.com 2-year warranty and free lifetime technical support.

Specifications

  • Product ID: SU2DUPERA11
  • Product Weight: 15.9 oz [450 g]
  • Product Measurements: Length: 5.3 in, Width: 3.5 in, Height: 1.1 in
  • Power Source: AC Adapter Included
  • Drive Connectors: 2 – 22 pin SATA Data + Power (7 + 15 pin) Receptacle, 2 – USB Type-A (4 pin) USB 2.0
  • Maximum Data Transfer Rate: 6.6 GB per minute
  • Drive Size: 2.5in & 3.5in
  • Compatible Drive Types: SATA & USB Flash Drive
  • Warranty: 2 Years

Source: The sample for this review was provided by StarTech. Please visit their website for more info and Amazon.

 

Product Information

Price: $796.99
Manufacturer: StarTech
Retailer: Amazon
Requirements:
  • 2.5/3.5” SATA SSDs/HDDs or USB attached storage
Pros:
  • Versatile
  • Supports any operating system
  • Basic functions are simple to use
Cons:
  • Expensive
  • No USB-3.0 support
  • Minimal Documentation / Instructions

Filed in categories: Reviews

Tagged: ,

StarTech USB/SATA Drive Duplicator and Eraser review originally appeared on on June 26, 2017 at 10:24 am.

Note: If you are subscribed to this feed through FeedBurner, please switch to our native feed URL http://the-gadgeteer.com/feed/ in order to ensure continuous delivery.

Julie’s favorite gear, LG G6, Treblab XR100 headphones, and more – Review updates


I have five quick review updates for you this week of reviews that I’ve posted in the last 2 years. Why go back and update old review? Because we like to follow up with updates for products that we continue to use well after the original review has been posted. This gives people a good idea of how a product stands up over time. So click through for the list of recently updated reviews and then scroll to the bottom of each review to read the newest update.

Peak Design Everyday Messenger bag review by Julie Strietelmeier
Nexus 6P review by Julie Strietelmeier and Dave Rees
LG G6 review by Julie Strietelmeier and Judie Stanford
Julie’s Favorite Gear
Treblab XR100 Bluetooth headphones review by Julie Strietelmeier
Moshi Audio Clarus earphones review by Julie Strietelmeier

 

Product Information

Price:

Filed in categories: Reviews

Tagged:

Julie’s favorite gear, LG G6, Treblab XR100 headphones, and more – Review updates originally appeared on on June 26, 2017 at 8:51 am.

Note: If you are subscribed to this feed through FeedBurner, please switch to our native feed URL http://the-gadgeteer.com/feed/ in order to ensure continuous delivery.